Why You Cannot Add dBm Values Directly

A gain in dB adds to a level in dBm because it multiplies one power by a ratio. Two signal powers must be added in milliwatts: two uncorrelated +20 dBm signals give 200 mW, which is 23.01 dBm, not 40 dBm.

Engineer’s note: Some new engineers feed +30 dBm and +30 dBm into a combiner and get +60 dBm, which would be a kilowatt out of two 1 watt signals. dBm is a physical quantity: convert to watts, add, then take the log again, and the answer is +33 dBm. Adding dBm values is like mixing two cups of 30-degree water and expecting 60 degrees.

For practitioners

What dBm and dB actually describe

A level in dBm is an absolute power, given relative to 1 mW:

PdBm=10log⁡10(P1 mW)P_{\text{dBm}} = 10 \log_{10}\left(\frac{P}{1\,\text{mW}}\right)

So 0 dBm is 1 mW, +20 dBm is 100 mW and +40 dBm is 10 W. The "m" tells you the number has a unit behind it.

A value in dB has no reference at all. It is the ratio between two powers:

GdB=10log⁡10(PoutPin)G_{\text{dB}} = 10 \log_{10}\left(\frac{P_{\text{out}}}{P_{\text{in}}}\right)

A 15 dB amplifier multiplies power by about 31.6. A cable with 2 dB of loss multiplies it by about 0.631. Neither number says anything about how much power is present. Each one only says what happens to whatever power goes in.

All the rules below come from one property of logarithms: log10(a·b) = log10(a) + log10(b). The logarithm turns multiplication into addition. Nothing turns log10(a + b) into a simple sum of logs, and that is the whole reason dBm values cannot be added.

Why dBm plus dB is valid

A gain stage multiplies one power by a ratio: P_out = P_in · G. Take 10·log10 of both sides and the multiplication becomes addition:

Pout,dBm=Pin,dBm+GdBP_{\text{out,dBm}} = P_{\text{in,dBm}} + G_{\text{dB}}

The left panel of the figure shows a 0 dBm source driving a +15 dB amplifier, followed by a cable with −2 dB of loss. The output is 0 + 15 − 2 = 13 dBm. In linear terms that is 1 mW × 31.62 × 0.631 ≈ 19.95 mW, which is 13 dBm. The dB arithmetic and the watt arithmetic agree, because there is only one power and every stage just scales it.

Valid: dBm + dBSource0 dBmAmplifier+15 dBCable−2 dB13 dBmOutput0 + 15 − 2 = 13 dBmdBm + dB = dBm(a gain multiplies one power)Invalid: dBm + dBm0 dBm = 1 mWSource 1Source 20 dBm = 1 mWCombinerOutput3.01 dBm1 mW + 1 mW = 2 mW= 3.01 dBm (not 0 dBm)dBm + dBm:convert to mW first
Adding a dB gain or loss to a dBm level is valid, but two dBm powers have to be converted to milliwatts before they are added. Concept drawing.

The unit bookkeeping is worth memorising:

  • dBm + dB = dBm (a power scaled by a ratio)
  • dB + dB = dB (two ratios in cascade multiply into one ratio)
  • dBm − dBm = dB (the ratio of two powers)
  • dBm + dBm = no physical meaning

The last line fails because adding two logarithms multiplies their arguments. The sum of two dBm values is the log of P1 × P2, which has units of mW². That is not a power, and no combiner multiplies one signal by another.

Why dBm plus dBm fails

When two uncorrelated signals reach the same port, their powers add:

Ptotal=P1+P2P_{\text{total}} = P_1 + P_2

This sum happens in watts or milliwatts, not in dBm. The right panel of the figure shows two 0 dBm sources feeding a combiner. Each one is 1 mW, the total is 2 mW, and 2 mW is 10·log10(2) = 3.01 dBm. Adding the dBm numbers would give 0 + 0 = 0 dBm, as if the second source added nothing. The wrong answer can come out too low, as here, or far too high, as the next example shows.

To combine levels that are given in dBm, convert them, add them, and convert back:

Ptotal,dBm=10log⁡10(10P1/10+10P2/10)P_{\text{total,dBm}} = 10 \log_{10}\left(10^{P_1/10} + 10^{P_2/10}\right)

Here P1 and P2 are in dBm, and each term inside the bracket is a power in milliwatts.

Worked example: two +20 dBm signals

Two uncorrelated signals of +20 dBm each are combined.

  1. Convert to milliwatts: 10^(20/10) = 100 mW each.
  2. Add: 100 mW + 100 mW = 200 mW.
  3. Convert back: 10·log10(200) = 23.01 dBm.

Adding the dBm numbers instead gives 40 dBm, which is 10 W. That is 50 times the real 200 mW, an error of 16.99 dB. In a link budget or an interference estimate, an error that size changes the conclusion.

Spreadsheets make this mistake easy. If you have a column of interferer or spur levels in dBm, sum them as 10·log10(SUM(10^(x/10))). A plain SUM() of a dBm column gives a meaningless number.

Unequal levels, the 3 dB ceiling and the subtraction rule

For N equal uncorrelated signals, the total is N times one of them:

Ptotal,dBm=PdBm+10log⁡10NP_{\text{total,dBm}} = P_{\text{dBm}} + 10 \log_{10} N

With N = 2 that adds 3.01 dB, which matches both examples above.

When the levels are unequal, the stronger signal sets most of the total. Take +20 dBm and +10 dBm: 100 mW + 10 mW = 110 mW, which is 20.41 dBm. A signal 10 dB down adds only 0.41 dB. This gives two bounds that are useful as a sanity check. For two uncorrelated signals, the sum is never below the stronger one and never more than 3.01 dB above it. The upper bound is reached only when the two are equal.

Subtracting is the operation that does work directly in dBm. +20 dBm − (+10 dBm) = 10 dB tells you the first signal is ten times the second. That is how you read a carrier-to-interference ratio or a spur level relative to a carrier. The answer is a ratio in dB, not a level in dBm.

The rule P_total = P1 + P2 is for uncorrelated signals, such as independent noise sources or carriers on different frequencies. Coherent signals on the same frequency add as voltages, so the result depends on their relative phase. Two equal signals in phase give four times the power of one (+6.02 dB). In anti-phase they cancel. If you can't be sure the signals are uncorrelated, don't use the power sum.

In plain words · for students and beginners

Adding dBm values in plain words

An everyday picture: counting zeros

Think of dB as a way of counting zeros. Every 10 dB means "times ten". So 100 mW, which is 1 followed by two zeros, is +20 dBm. A gain of 20 dB means "add two zeros", or multiply by 100.

Adding zeros to a number is the same as multiplying it. That's why adding a gain in dB to a level in dBm works: an amplifier really does multiply the power.

Now pour two buckets of 100 mW together. You get 200 mW. You don't get 1 followed by four zeros (10,000 mW). Adding the "zero counts" of two buckets would mean multiplying the buckets together, and nothing in a circuit does that.

Where the picture breaks down: dB doesn't only come in whole zeros. 3 dB is about "times two", and 13 dBm is about 20 mW. The counting-zeros idea explains why dB values add. It won't give you exact numbers.

The same example, step by step

Two separate signals of +20 dBm each go into one cable.

  1. Turn each one into milliwatts. +20 dBm is 100 mW.
  2. Add the milliwatts: 100 + 100 = 200 mW.
  3. Turn the total back into dBm: 200 mW is 23.01 dBm.

The wrong way is 20 + 20 = 40 dBm. That is 10 W, which is 50 times too much.

Wrong: adding the dBm numbers+20 dBm++20 dBm40 dBm = 10 Wwrong50 times too muchRight: convert to mW, then add+20 dBm100 mW+20 dBm100 mW100 mW + 100 mW= 200 mW23.01 dBmcorrect
Uncorrelated powers add in watts: P_total = P1 + P2, so two +20 dBm signals give 23.01 dBm, not 40 dBm. Concept drawing.

The same thing happens with smaller signals. Two 0 dBm signals are 1 mW each. Together they make 2 mW, which is 3.01 dBm, not 0 dBm.

Mistakes beginners make

  • Adding dBm columns. If two signals are combined, add their powers in mW, never their dBm numbers.
  • Thinking dB and dBm are the same thing. dBm is an amount of power (relative to 1 milliwatt). dB is only a ratio, like "times 100".
  • Expecting a big jump. Two equal signals together are only 3.01 dB stronger than one. If your answer jumps by tens of dB, check your method.
  • Forgetting the condition. The "add the milliwatts" rule is for unrelated (uncorrelated) signals, meaning signals that don't keep a fixed timing relationship with each other.

Remember

  • dBm + dB = dBm: a gain or loss multiplies one power.
  • Two powers add in watts or milliwatts: P_total = P1 + P2, then convert back to dBm.
  • dBm − dBm = dB: subtracting two levels gives their ratio.

Frequently asked questions

What is 0 dBm plus 0 dBm?

For two uncorrelated signals it is 1 mW + 1 mW = 2 mW, which is 3.01 dBm. Adding the dBm numbers gives 0 dBm, which is wrong.

Why can I add dB gain to a dBm level?

A gain in dB is a ratio, and adding logarithms is the same as multiplying. Adding 15 dB to a dBm level multiplies that one power by about 31.6, so the result is still a power in dBm.

What does subtracting two dBm values give?

It gives the ratio of the two powers in dB. For example, +20 dBm minus +10 dBm is 10 dB, so the first power is ten times the second.

How do I add two signal powers given in dBm?

Convert each level to milliwatts with P = 10^(dBm/10), add the milliwatt values, then convert back with 10·log10(P_total / 1 mW). This works for uncorrelated signals.

References and further reading