Multi-Section L-Networks for Wider Matching Bandwidth

Splitting a 5 to 500 ohm match into N L-sections with equal resistance ratios cuts the Q of each section from 9.95 to 3 with two sections and to 1.908 with three. Use R_k = R_low (R_high/R_low)^(k/N) and Q = sqrt((R_high/R_low)^(1/N) − 1).

Engineer’s note: When the impedance ratio is large and you need a wide band, as with UWB or a multiband antenna, chain several low-Q L-networks in series. Much like a Chebyshev filter, it builds a few gentle ripples that together cover a much wider band. More parts, but the bandwidth is there.

For practitioners

Why a single L-section is narrowband

An L-network that matches two resistances has no free design parameter. Once you fix R_low and R_high, the Q of the network is fixed too:

Q=RhighRlow−1Q = \sqrt{\frac{R_{\text{high}}}{R_{\text{low}}} - 1}

The series reactance is X_s = Q · R_low and the shunt reactance is X_p = R_high / Q. At the center frequency, the series element and the shunt element turn R_high into R_low, and the leftover reactance cancels exactly. Off center, the series reactance and the shunt susceptance both change with frequency, so the cancellation fails. How quickly it fails depends on Q. The usable fractional bandwidth is roughly inversely proportional to Q.

For a 5 Ω to 500 Ω transformation, the ratio is 100 and Q = √99 = 9.95. The reactances at center are X_s = 9.95 × 5 = 49.75 Ω and X_p = 500 / 9.95 = 50.25 Ω. This is a high-Q, narrow match. A large resistance ratio is typical at the low-impedance port of a power device, which is exactly where you often need the most bandwidth.

The topology choices, L versus Pi versus T, are covered in RF Matching Networks: L, Pi and T. A Pi or T network lets you choose a Q higher than the L-network value, which gives you a narrower match. To get a lower Q, you have to cascade L-sections.

Splitting the transformation into equal ratios

Put N L-sections in series and give each one a smaller step. The resistances at the internal nodes are virtual: they are the impedances each section sees looking toward the load at the center frequency. Space them geometrically:

Rk=Rlow(RhighRlow)k/N,k=0,1,…,NR_k = R_{\text{low}} \left( \frac{R_{\text{high}}}{R_{\text{low}}} \right)^{k/N}, \quad k = 0, 1, \ldots, N

Every section then has the same ratio, (R_high/R_low)^(1/N), and the same Q:

Qsection=(RhighRlow)1/N−1Q_{\text{section}} = \sqrt{\left( \frac{R_{\text{high}}}{R_{\text{low}}} \right)^{1/N} - 1}

Equal ratios are the right choice for a simple reason. The product of the section ratios always equals R_high/R_low, which is 100 here. Q increases with ratio, so any uneven split gives one section a ratio above the geometric value. That section then has the highest Q and limits the bandwidth. Geometric spacing makes the worst section Q as low as it can be for a given N.

A common mistake is to use the arithmetic midpoint. For 5 Ω to 500 Ω that is 252.5 Ω. The first section then has a ratio of 50.5 and Q ≈ 7.04, and the second has a ratio of about 1.98. The geometric midpoint, √(5 × 500) = 50 Ω, gives Q = 3 in both sections.

Worked example: 5 Ω to 500 Ω in one, two and three sections

SectionsRatio per sectionIntermediate resistancesQ per section
1100none√99 = 9.95
21050 Ω√9 = 3
3100^(1/3) = 4.64223.21 Ω, 107.7 Ω√3.642 = 1.908

Check the three-section chain: 5 × 4.642 = 23.21 Ω, 23.21 × 4.642 = 107.7 Ω, 107.7 × 4.642 = 500 Ω.

For the two-section version, the reactances at center are 15 Ω series and 16.67 Ω shunt in the first section, then 150 Ω series and 166.7 Ω shunt in the second.

The three-section low-pass version uses the same rule in every section. The series inductor sits on the low-resistance side and the shunt capacitor to ground sits on the high-resistance side:

  • Section 1, 5 Ω to 23.21 Ω: X_L = 1.908 × 5 = 9.54 Ω, X_C = 23.21 / 1.908 = 12.16 Ω
  • Section 2, 23.21 Ω to 107.7 Ω: X_L = 1.908 × 23.21 = 44.29 Ω, X_C = 107.7 / 1.908 = 56.45 Ω
  • Section 3, 107.7 Ω to 500 Ω: X_L = 1.908 × 107.7 = 205.5 Ω, X_C = 500 / 1.908 = 262.1 Ω
Section 15 Ω to 23.21 ΩSection 223.21 Ω to 107.7 ΩSection 3107.7 Ω to 500 ΩSource5 ΩL1C123.21 Ωratio 4.642Q = 1.908L2C2107.7 Ωratio 4.642Q = 1.908L3C3ratio 4.642Q = 1.908Load500 ΩOne L-section 5 Ω to 500 Ω:Q = 9.95
Three-section low-pass L cascade from 5 Ω to 500 Ω with geometric intermediate resistances of 23.21 Ω and 107.7 Ω, so every section has ratio 4.642 and Q = 1.908. Concept drawing.

Each section has ratio 4.642 and Q = 1.908, compared with Q = 9.95 for one L-section doing the whole job. To turn the reactances into component values, divide by ω for the inductors and invert ωX for the capacitors at your center frequency. You can also run each section separately through the L-network matching calculator, using the intermediate resistances as source and load.

How far to push N

The gain from each added section gets smaller quickly:

  • 1 → 2 sections: Q falls from 9.95 to 3, a factor of 3.3
  • 2 → 3 sections: Q falls from 3 to 1.908, a factor of 1.57
  • 3 → 4 sections: ratio 100^(1/4) = 3.162, Q = √2.162 = 1.470, a factor of 1.30

For large N, ratio^(1/N) − 1 ≈ ln(ratio)/N, so the section Q falls only as 1/√N. For a ratio of 100 that is Q ≈ √(4.605/N). Each added section, by contrast, adds two parts, their loss, their parasitics and their tolerance. In most designs, two or three sections cover most of the available benefit.

Per-section Q is a design guide. It is not an exact prediction of the passband. Away from center, each section no longer sees its ideal virtual resistance, so the sections load each other. Simulate the full cascade and judge it by return loss across the band.

Practical choices in the cascade

The sections don't all need the same orientation. A low-pass cascade like the one above adds harmonic rejection, which is useful after a power stage. A high-pass section can provide DC blocking. Mixing them changes the out-of-band response but not the per-section Q at center. The trade-offs are covered in L-Network: Low-Pass or High-Pass?.

If the low-resistance port has its own reactance, such as a device output capacitance, absorb it into the first element. Any reactance you absorb raises the effective Q at that port, so the gain from the cascade is limited by the device as well as by the network. The first section has the smallest reactances, 9.54 Ω and 12.16 Ω in the example, so it is the most sensitive to layout. Keep that section physically compact.

In plain words · for students and beginners

Multi-section L-networks in plain words

One big step or several small ones

Suppose you need to climb from a low floor to a high one. One huge step works only if you land it exactly right. A staircase with several smaller steps is easier, and it still works if your footing is a little off. A matching network behaves in a similar way. It changes a low resistance into a high one, and a big jump done in one go only works over a narrow range of frequencies. Several smaller jumps work over a wider range.

The analogy breaks down at one point. Real stairs get easier the more steps you add. In a matching network, every extra step adds parts, and each part wastes a little power and adds its own errors. After two or three steps, adding more gives you little extra benefit.

The same example, step by step

We want to match 5 ohm to 500 ohm. That is a ratio of 100, because 500 / 5 = 100.

  1. One section. Q (a number that says how sharp and narrow the match is) = √(100 − 1) = 9.95. This is a narrow match.
  2. Two sections. Each step must multiply the resistance by the same amount, so each step is √100 = 10. The middle point is 5 × 10 = 50 ohm. Each step has Q = √(10 − 1) = 3.
  3. Three sections. Each step multiplies by the cube root of 100, which is 4.642. The points are 5, 23.21, 107.7 and 500 ohm. Each step has Q = √(4.642 − 1) = 1.908.
Matching 5 ohm to 500 ohm, log resistance axis5102050100200500Resistance (ohm, log)Q = 9.95Q = 3Q = 3Q = 1.908Q = 1.908Q = 1.9085023.21107.71 sectionratio 1002 sectionsratio 10 per step3 sectionsratio 4.642 per stepNumber of sections
Geometric resistance steps from 5 ohm to 500 ohm for one, two and three L-network sections, drawn on a log scale so that equal ratios look like equal step heights. Computed from the formula.

On a log scale (a scale where each multiplication by the same number looks like the same distance), equal ratios look like equal step heights. The lower Q in each step is what widens the match.

Mistakes beginners make

  • Splitting the difference. The halfway point between 5 and 500 ohm is 252.5 ohm, but using it as the middle step is wrong. The first step then has a ratio of 50.5, which is still steep. Multiply by equal amounts at each step. Don't add equal amounts.
  • Expecting more sections to keep helping. Going from one section to two cuts Q a lot. Going from three to four cuts it only a little.
  • Ignoring the small parts. The first step on the 5 ohm side uses very small reactances (opposition to AC current from a coil or capacitor). Short board traces can upset it.

Remember

  • Choose the middle resistances so that every step has the same ratio. For 5 to 500 ohm in two steps, that is 50 ohm.
  • A smaller ratio per step gives a lower Q, and a lower Q gives a wider match.
  • Two or three sections give most of the benefit. Beyond that, extra parts cost more than they help.

Frequently asked questions

How do I choose the intermediate resistances in a multi-section L-network?

Space them geometrically: R_k = R_low (R_high/R_low)^(k/N). Every section then transforms by the same ratio, and the highest section Q is as low as it can be for that number of sections.

Why does a multi-section L-network have more bandwidth than a single L-section?

Each section steps the resistance by a smaller ratio, so each section has a lower Q. Lower Q means the reactances drift away from cancellation more slowly as frequency moves off center, so the match holds over a wider band.

What is the Q of each section when matching 5 ohm to 500 ohm?

One section has Q = 9.95. Two sections through 50 ohm have Q = 3 each. Three sections through 23.21 ohm and 107.7 ohm have Q = 1.908 each.

Should I use the arithmetic mean as the intermediate resistance?

No. For 5 to 500 ohm the arithmetic mean is 252.5 ohm, which leaves the first section with a ratio of 50.5 and Q of about 7.04. The geometric mean, 50 ohm, gives Q = 3 in both sections.

References and further reading