dBi vs dBd: The Two References for Antenna Gain
dBi references antenna gain to a lossless isotropic radiator, dBd to a lossless half-wave dipole. Because the dipole's directivity is 1.64, or 2.15 dBi, you convert with dBi = dBd + 2.15, so 5 dBd equals 7.15 dBi.
Engineer’s note: Antenna brochures almost always quote gain in dBi rather than dBd, since it reads 2.15 dB bigger (dBi = dBd + 2.15). Before you drop an antenna gain into a system budget, ask whether it's just the flattering reference or a realistic measured figure for an antenna that size.
For practitioners
Antenna gain is always a ratio, and a ratio needs a reference. Two references are in common use: the isotropic radiator, which gives dBi, and the half-wave dipole, which gives dBd. They differ by a fixed 2.15 dB. If you mix them up, your link budget is off by that amount, and nothing on the bench will point to the cause.
What the two references are
dBi is gain relative to a hypothetical lossless isotropic radiator. It radiates the same power density in every direction, so its pattern is a perfect sphere. No real antenna can do this, but it makes a clean mathematical baseline. Its directivity is 1 by definition, which is 0 dBi.
dBd is gain relative to a lossless half-wave dipole. Unlike the isotropic source, this reference can be built and measured on a range. That is why it shows up in older literature and on some antenna datasheets.
Both references are lossless. They define a direction-dependent power density for a given radiated power. So a gain figure in either unit tells you how much stronger the antenna's peak radiation is than the reference's peak radiation, for the same accepted power. For a real antenna, gain = radiation efficiency × directivity, so losses in the antenna itself pull the gain below the directivity.
Directivity and the isotropic baseline
Directivity compares the radiation intensity in the strongest direction with the average over all directions:
Here U_max is the peak radiation intensity in watts per steradian, and P_rad is the total radiated power. For the isotropic radiator, U is the same everywhere and equals P_rad / 4π, so D = 1. Any antenna that sends more power in one direction must send less in others, since the total is fixed. Directivity measures that redistribution.
The half-wave dipole has the textbook E-plane pattern proportional to cos(π/2 · cos θ) / sin θ in field. Here θ is measured from the dipole axis. The pattern has nulls along the axis and a maximum broadside. Integrating this pattern over the sphere gives a directivity of about 1.64.
The figure shows both patterns on a linear power scale in the plane that contains the dipole. The circle of radius 1 is the isotropic radiator. The figure-eight reaches 1.64 broadside and falls to zero along the dipole axis. Both shapes enclose the same total radiated power in three dimensions. The dipole takes power away from the axis and puts it broadside.
Where 2.15 dB comes from
Convert the dipole's directivity to decibels:
So a lossless half-wave dipole has a peak gain of 2.15 dBi. By definition, the same antenna is 0 dBd. That fixes the offset between the two scales:
Because both quantities are already logarithmic, the conversion is a plain addition. It applies only to peak gain or gain in a stated direction. It does not apply to a full pattern taken in different planes.
Do not confuse the half-wave dipole with the short (Hertzian) dipole. A short dipole has a directivity of 1.5, which is 1.76 dBi. The half-wave dipole is slightly more directive, by 2.15 − 1.76 = 0.39 dB. The dBd unit always means the half-wave dipole. If you use the short-dipole value, every conversion will be off by 0.39 dB.
Worked example: 5 dBd into a link budget
Suppose an antenna is specified at 5 dBd and you need its EIRP. The dB form of the link budget is:
This equation expects gain in dBi, so convert first:
- G = 5 dBd + 2.15 dB = 7.15 dBi
- EIRP = P_tx + 7.15 − L_feed (all in dB or dBm)
If you put the 5 dBd value straight into the dBi slot, the EIRP comes out 2.15 dB low. In linear terms, 2.15 dB is the same factor of 1.64. So the error means you assumed about 39 % less radiated power density in the main beam than the antenna actually produces. The adding of gains and losses itself is covered in dB and dBm in a Signal Chain.
Where the confusion bites
- Unlabelled "dB". A gain number with no suffix cannot be converted. Find out the reference before it goes into a budget.
- Effective radiated power. Some radiated-power figures are referenced to a dipole (ERP) and some to an isotropic radiator (EIRP). These follow the same rule: EIRP = ERP + 2.15 dB.
- Mismatch versus gain. Gain in dBi or dBd assumes the antenna accepts the power delivered to it. Reflected power at the feed is a separate loss and goes into the feed-loss term. See Phone Antenna S11 for how return loss relates to radiated power.
- Peak versus average. Both units describe the peak (or a stated direction). An antenna with high dBi gain has a narrow beam, not more total power.
In plain words · for students and beginners
dBi and dBd in plain words
An everyday analogy
Think of a bare light bulb hanging in a room. It lights every direction equally. That is the isotropic radiator, the "0 dBi" reference. Now picture a lamp shade that blocks light going up and down and sends it out sideways instead. The total light is the same, but sideways it looks brighter. A half-wave dipole does the same with radio waves. Its sideways brightness is 1.64 times the bare bulb's.
dBi means "compared with the bare bulb." dBd means "compared with the lamp with a shade." Because the shaded lamp already starts 1.64 times brighter sideways, any antenna gets a smaller number in dBd than in dBi.
Where the analogy breaks down: a real bare bulb exists, but a true isotropic antenna does not. It is a mathematical idea. Also, a lamp shade absorbs some light, while the reference dipole is assumed to have no loss at all.
The same example, step by step
- The antenna is rated 5 dBd.
- The dipole reference is 2.15 dB above the isotropic one. This comes from 10 log10(1.64) = 2.15. (A decibel, dB, is a logarithmic way to write a power ratio.)
- Add them: 5 + 2.15 = 7.15 dBi.
- Put 7.15 dBi into the transmitter formula. EIRP (the power an isotropic antenna would need to give the same signal in the main direction) = transmit power + 7.15 − cable loss.
The two number lines in the figure show the rule. Every dBd value lines up with a dBi value 2.15 higher: 0 with 2.15, 3 with 5.15, 5 with 7.15, 10 with 12.15.
Mistakes beginners make
- Ignoring the letter at the end. "5 dB" alone could mean 5 dBi or 7.15 dBi. Always check if it is i or d.
- Subtracting instead of adding. Going from dBd to dBi, you add 2.15. Going from dBi to dBd, you subtract it.
- Using the wrong dipole. A very short dipole is 1.76 dBi, not 2.15 dBi. dBd always refers to the half-wave dipole.
- Thinking gain creates power. An antenna with gain only concentrates power in some directions. It takes power away from other directions to do so.
Remember
- dBi compares to a perfect sphere-shaped radiator. dBd compares to a half-wave dipole.
- dBi = dBd + 2.15, so 5 dBd = 7.15 dBi.
- Link budgets use dBi, so convert before you add.
Related pages on RF View
Frequently asked questions
How do I convert dBd to dBi?
Add 2.15 dB. An antenna rated at 5 dBd is 7.15 dBi, and 0 dBd is 2.15 dBi.
Why is the difference between dBi and dBd exactly 2.15 dB?
A lossless half-wave dipole has a directivity of about 1.64 relative to an isotropic radiator. Expressed in decibels, 10 log10(1.64) = 2.15 dB, so the dipole reference sits 2.15 dB above the isotropic one.
Which unit should I use in a link budget, dBi or dBd?
Use dBi. The standard form EIRP (dBm) = transmit power (dBm) + antenna gain (dBi) - feed loss (dB) assumes an isotropic reference, so convert any dBd figure first by adding 2.15 dB.
Is a short dipole the same reference as a half-wave dipole?
No. A short (Hertzian) dipole has a directivity of 1.5, or 1.76 dBi, while a half-wave dipole has 1.64, or 2.15 dBi. The dBd unit always refers to the half-wave dipole.