Shorted and Open Line Stubs as Inductors and Capacitors

A lossless shorted stub gives Zin = jZ0·tan βl and an open stub gives −jZ0·cot βl, so a 50 Ω λ/8 stub at 1 GHz acts as 7.96 nH when shorted or 3.18 pF when open. Below 90° the shorted stub is inductive and the open stub is capacitive. Between 90° and 180° the signs swap.

Engineer’s note: At mmWave, tens of GHz, PCB stubs replace SMD inductors and capacitors, which carry too many parasitics. An open stub radiates from its end, though, leaking energy and coupling to a nearby shield can. To keep that under control I'd use a shorted stub, tied to ground through a via.

For practitioners

A short length of transmission line with a short or an open at its far end has no resistance in the ideal case. All it can show at its input is reactance. Whether that reactance is inductive or capacitive, and how large it is, depends on only three things: the termination, the characteristic impedance Z0, and the electrical length βl. That is why a stub can stand in for an inductor or a capacitor in matching networks and bias circuits. It also explains why the substitution only holds over a limited band.

Input impedance of a terminated lossless line

For a lossless line of characteristic impedance Z0, length l and phase constant β = 2π/λ, terminated in a load ZL, the input impedance is:

Zin=Z0ZL+jZ0tan⁡βlZ0+jZLtan⁡βlZ_{\text{in}} = Z_0 \frac{Z_L + j Z_0 \tan \beta l}{Z_0 + j Z_L \tan \beta l}

Two terminations matter here.

Shorted end (ZL = 0). The numerator becomes jZ0·tan βl and the denominator becomes Z0:

Zin,short=jZ0tan⁡βlZ_{\text{in,short}} = j Z_0 \tan \beta l

Open end (ZL → ∞). Divide the top and bottom by ZL and let ZL go to infinity. You are left with Z0 / (j tan βl):

Zin,open=−jZ0cot⁡βlZ_{\text{in,open}} = -j Z_0 \cot \beta l

Both results are purely imaginary. A lossless stub stores energy and dissipates none. In practice, conductor and dielectric loss add a small real part, but the reactive behaviour described here is what sets the stub's function.

Where the stub is inductive and where it is capacitive

Write the input impedance as jX. For the shorted stub, X/Z0 = tan βl. For the open stub, X/Z0 = −cot βl. Plotting both against βl shows the full behaviour over one half-wavelength.

543210−1−2−3−4−50°45°90°135°180°0λ/8λ/43λ/8λ/2Electrical length βl (degrees)Normalized reactance X/Z0 (unitless)Shorted stub: X/Z0 = tan βlOpen stub: X/Z0 = −cot βlInductive (X > 0)Capacitive (X < 0)tan 45° = +1−cot 45° = −1tan βl → ±∞shorted looks open−cot 90° = 0open looks short90° to 180°: signs swapshorted stub → capacitiveopen stub → inductive
Normalized input reactance of lossless shorted (tan βl) and open (−cot βl) stubs over one half-wavelength, showing the inductive and capacitive regions and the quarter-wave inversion at 90°. Computed from the formula.

Read the plot from left to right:

  • 0° < βl < 90°. tan βl is positive, so the shorted stub is inductive. −cot βl is negative, so the open stub is capacitive. At βl = 45° the shorted stub sits at X/Z0 = +1 and the open stub at X/Z0 = −1.
  • βl = 90° (λ/4). tan βl goes to ±∞, so the shorted stub looks like an open circuit. −cot βl passes through zero, so the open stub looks like a short circuit. This is the quarter-wave inversion seen from inside the stub.
  • 90° < βl < 180°. The signs swap. tan βl is negative, so the shorted stub is now capacitive. −cot βl is positive, so the open stub is now inductive.
  • βl = 180° (λ/2). The shorted stub returns to a short and the open stub returns to an open. The pattern repeats every half-wavelength.

The rule for short stubs is simple. Below λ/4, a shorted stub is an inductor and an open stub is a capacitor. Most practical stubs are kept well below λ/4 for that reason, and also because shorter stubs vary less with frequency.

Converting reactance to nH and pF

To give a stub a lumped value at angular frequency ω = 2πf, set its reactance equal to that of the lumped part.

For a shorted stub in the inductive region, ωL = Z0·tan βl:

Leq=Z0tan⁡βl2πfL_{\text{eq}} = \frac{Z_0 \tan \beta l}{2 \pi f}

For an open stub in the capacitive region, 1/(ωC) = Z0·cot βl:

Ceq=tan⁡βl2πfZ0C_{\text{eq}} = \frac{\tan \beta l}{2 \pi f Z_0}

You can run these in reverse to size a stub. For a required reactance X, the shorted-stub length is βl = arctan(X/Z0). The open-stub length for a required capacitive reactance |X| is βl = arctan(Z0/|X|). The choice of Z0 is a design lever. A high-impedance line reaches a given inductive reactance in fewer degrees, and a low-impedance line reaches a given capacitive reactance in fewer degrees.

Worked example: 50 Ω λ/8 stubs at 1 GHz

Take a 50 Ω line one-eighth of a wavelength long at 1 GHz, so βl = 360°/8 = 45° and tan 45° = 1.

Shorted end. Zin = j50 × tan 45° = j50 Ω. The equivalent inductance is:

L = 50 / (2π × 1e9) ≈ 7.96 nH

Open end. Zin = −j50 × cot 45° = −j50 Ω. The equivalent capacitance is:

C = 1 / (2π × 1e9 × 50) ≈ 3.18 pF

So the same piece of line gives either 7.96 nH or 3.18 pF at 1 GHz, depending only on what you put at its far end.

Why the equivalent value only holds near one frequency

A real inductor's reactance rises linearly with frequency. A shorted stub's reactance follows tan βl, and βl itself is proportional to frequency. Here is the 1 GHz shorted λ/8 stub compared with an ideal 7.96 nH inductor at other frequencies:

FrequencyβlStub X = 50·tan βlIdeal 7.96 nH XStub L_eq
500 MHz22.5°20.7 Ω25.0 Ω6.59 nH
1 GHz45°50.0 Ω50.0 Ω7.96 nH
1.5 GHz67.5°120.7 Ω75.0 Ω12.8 nH
2 GHz90°∞100.0 Ω—

The stub matches the inductor at exactly one frequency. Below that frequency its equivalent inductance is lower, and above it the equivalent inductance is higher. At 2 GHz the stub is a quarter-wave long and looks like an open circuit. The open stub behaves the same way in mirror image: its equivalent capacitance grows with frequency and goes to infinity at λ/4, where the stub becomes a short.

For small βl, tan βl ≈ βl and the stub approaches a true lumped element. A short shorted stub tends to the line's series inductance per unit length times l. A short open stub tends to its shunt capacitance per unit length times l. The shorter the stub is in degrees, the wider the band over which the lumped approximation holds.

A stub designed as an inductor at f0 becomes an open at 2·f0 when it is λ/8 long at f0. If a harmonic or an out-of-band signal falls near that frequency, the stub no longer behaves like the part it replaced. Check the stub's reactance across the whole band of interest, not only at the design frequency.

On a Smith chart, both stubs move along the outer circle (|Γ| = 1). The shorted stub starts at the short-circuit point and the open stub starts at the open-circuit point. Each rotates toward the generator by 2βl. Increasing frequency increases that rotation, which is the same frequency-dependent effect shown in the table.

In plain words · for students and beginners

Line stubs as inductors and capacitors in plain words

An everyday picture

Think of shouting into a long pipe. If the far end is closed, the sound bounces back one way. If the far end is open, it bounces back a different way. What you hear at your end depends on how long the pipe is and what is at the far end.

A stub works the same way. A stub is a short piece of transmission line attached at one end only. The signal goes down the stub, reflects off the far end, and comes back. The returning wave is shifted in time, so at the input the stub "looks like" a coil (an inductor) or a small plate pair (a capacitor), even though it is just metal and insulator.

The picture breaks down in one place. A pipe's echo is easy to hear at any pitch, but a stub only copies a given inductor or capacitor at one frequency. Change the frequency and the stub "becomes" a different part.

The worked example, step by step

Shorted λ/8 stubZ0 = 50 Ωλ/8, βl = 45°shortZin = j50 Ωat 1 GHzL = 7.96 nHOpen λ/8 stubZ0 = 50 Ωλ/8, βl = 45°openZin = -j50 Ωat 1 GHzC = 3.18 pFEquivalent value holds only near 1 GHz
A shorted and an open 50 Ω λ/8 stub at 1 GHz with their equivalent inductor and capacitor, where the equivalent value holds only near 1 GHz. Concept drawing.
  1. Take a 50 Ω line. (50 Ω is its characteristic impedance, the ratio of voltage to current for a wave moving along it.)
  2. Make it one-eighth of a wavelength long at 1 GHz. One full wavelength is 360°, so one-eighth is 45°.
  3. Short the far end. The formula is Zin = j × 50 × tan 45°. tan 45° = 1, so Zin = j50 Ω. The "j" with a plus sign means inductive.
  4. Turn 50 Ω of inductive reactance into henries: L = 50 / (2π × 1,000,000,000) ≈ 7.96 nH.
  5. Leave the far end open instead. Zin = −j × 50 × cot 45° = −j50 Ω. The minus sign means capacitive.
  6. Turn that into farads: C = 1 / (2π × 1,000,000,000 × 50) ≈ 3.18 pF.

It is the same line with two different endings, and it gives two different parts.

Where it flips

Up to a quarter wavelength (90°), a shorted stub acts like an inductor and an open stub acts like a capacitor. At exactly a quarter wavelength, something odd happens. The shorted stub looks like an open circuit, and the open stub looks like a short. Past that point, up to half a wavelength, they swap roles: the shorted one acts like a capacitor and the open one acts like an inductor.

Mistakes beginners make

  • Treating the stub's value as fixed. 7.96 nH is right at 1 GHz only. At 1.5 GHz the same stub acts like about 12.8 nH.
  • Mixing up the endings. Shorted and short means inductor. Open and short means capacitor. Remember "short-short-L".
  • Forgetting the quarter-wave point. A stub that is a coil at one frequency can be an open circuit at twice that frequency.
  • Measuring length in millimetres only. What matters is length in degrees (or fractions of a wavelength) at the frequency you care about.

Remember

  • Shorted stub: Zin = jZ0·tan βl. Open stub: Zin = −jZ0·cot βl.
  • Below 90°, shorted means inductive and open means capacitive. At 90° they flip.
  • A 50 Ω λ/8 stub at 1 GHz gives 7.96 nH when shorted or 3.18 pF when open, and only near 1 GHz.

Frequently asked questions

Is a shorted stub an inductor or a capacitor?

A lossless shorted stub has Zin = jZ0·tan βl. It is inductive for electrical lengths between 0° and 90° and capacitive between 90° and 180°.

What inductance does a 50 Ω shorted λ/8 stub give at 1 GHz?

At βl = 45°, Zin = j50 Ω. At 1 GHz that equals L = 50 / (2π × 1e9) ≈ 7.96 nH.

Why does an open quarter-wave stub act like a short circuit?

An open stub has Zin = −jZ0·cot βl, and cot 90° = 0. At exactly λ/4 the input impedance is therefore zero, which is a short circuit at that frequency.

Can a stub replace a lumped inductor over a wide band?

Not exactly. The stub's reactance follows tan βl or cot βl, not ωL or 1/(ωC), so its equivalent L or C is only correct near the design frequency.

References and further reading